WARPIG Tech Talk - Air


Home Pictures Technical Tournament Recreational Fields Stores
Beginner Info News And Articles Links Resources Video Contact Us Search

WARPIG Tech Talk - Air
Re: Options

[ Follow Ups ] [ Post Followup ] [ WARPIG Tech Talk - Air ]

Posted by flow on October 16, 2002 at 09:44:22:

In Reply to: BIG problem with ACI bulldog posted by short_round on October 16, 2002 at 00:08:44:

: I took my ACI Bulldog HPA tank (3k psi adjustable reg) in for hydrostat testing. it passed inspection and i got it filled. Unfortunatly the guys who tested it backed the regulator adjustment screw all the way out. The output was reading 1500 psi. I have not used the tank in over 3 years so I could not remember if you where supposed to tighten the screw or losten it to reduce preasure. Since on most regulators higher spring tension means higher preasure I tried lostening the nut. The preasure rose, so I tightened it, it rose again and burst the output 1800 psi disc, and I can only asume damaged my gauges and probably the reg. So far the only thing I can come up with is that the screw was backed out so far that it was not properly adjusting the regulator, any ideas? also can I assume that the regualtor is damaged? where can I find a replacement burst disk if it even is a burst disk and not a check valve? Apparently ACI no longer makes the Bulldog with adjustable output, is there anywhere I can obtain a manual for it with an exploded view of the parts? I think the moral of this story is be carful who you get to check your tank, and assume NOTHING!

I know that ACI should have replacement parts for the burst disc. If you run into a dead end, get a reg swap with CrossFire. They are very good and their price is extreemly fair. Good Luck

Follow Ups:

Post a Followup

Show your name as:

E-Mail address (eg: joeschmoe@aol.com):

Show your e-mail address?

Your Password:

Don't have a password? CLICK HERE - Forgot your password? CLICK HERE

Subject:

Subject:Message:
: : I took my ACI Bulldog HPA tank (3k psi adjustable reg) in for hydrostat testing. it passed inspection and i got it filled. Unfortunatly the guys who tested it backed the regulator adjustment screw all the way out. The output was reading 1500 psi. I have not used the tank in over 3 years so I could not remember if you where supposed to tighten the screw or losten it to reduce preasure. Since on most regulators higher spring tension means higher preasure I tried lostening the nut. The preasure rose, so I tightened it, it rose again and burst the output 1800 psi disc, and I can only asume damaged my gauges and probably the reg. So far the only thing I can come up with is that the screw was backed out so far that it was not properly adjusting the regulator, any ideas? also can I assume that the regualtor is damaged? where can I find a replacement burst disk if it even is a burst disk and not a check valve? Apparently ACI no longer makes the Bulldog with adjustable output, is there anywhere I can obtain a manual for it with an exploded view of the parts? I think the moral of this story is be carful who you get to check your tank, and assume NOTHING! : I know that ACI should have replacement parts for the burst disc. If you run into a dead end, get a reg swap with CrossFire. They are very good and their price is extreemly fair. Good Luck

[ Follow Ups ] [ Post Followup ] [ WARPIG Tech Talk - Air ]

Copyright © 1992-2019 Corinthian Media Services.

WARPIG's webmasters can be reached through our feedback form. All articles and images are copyrighted and may not be redistributed without the written permission of their original creators and Corinthian Media Services. The WARPIG paintball page is a collection of information and pointers to sources from around the internet and other locations. As such, Corinthian Media Services makes no claims to the trustworthiness or reliability of said information. The information contained in, and referenced by WARPIG, should not be used as a substitute for safety information from trained professionals in the paintball industry.