Posted by: Razorpb on November 07, 2002 at 12:52:14

I've just yesterday gone back to my original modified stock valve. I was using a Rat 3:16 for awhile. I had to raise my operating pressure 25 psi over the mod stock, and my consistency along with accuracy was suffering. I previously enjoyed a spread of 9 fps over ten shots, I had my velocity set at 280 and never shot hot or under 275. Seeing some of the posts on sweetspotting and with some feedback I gave it a try and was dissapointed with the results (sorry guy's, maybe it's just me) it seemed like I almost went in a circle and ended up worse, oh well I can deal with 600 shots from a 68 3000. So now I've come to the conclusion that I should go back to my best setup. Blue Maddman springs front and back, modified stock valve (looks similar to a Turbo valve), wgp stock inline set to 250 psi. I have the green springs in right now and the reg is at 300 psi, but I'm going to go back to blues, drop 50 psi, and see if that tightens up the variance. I can arrange milling if your interested. Razor : : I've been using mine for almost 2 years now with no problems other than wear (due due milling). I've run as low as 250 psi without flow problems or shootdown. It will work on any 2000+ stock cocker, or any pre 2000 with the use of a 2000+ back block. : : Razor : : : : : is the ANS quick pull bolt good? im considering getting it because the design on the face is supposed to break up air more evenly and put a softer punch on the ball. the main reason for the question is, the site i purchace on says it "will only work on 2000 cockers". not 2000+. but arent the bolt shafts the same. the site is : : : http://www.actionvillage.com/011-9010-850-5.html : what valve do you use?

Follow Ups: Re: hey razor Sinagent 21:37:15 11/10/02 (0) Post a Followup Show your name as: DefaultRealnameBothNickname E-Mail address (eg: joeschmoe@aol.com): Show your e-mail address? DefaultYesNo Your Password: Don't have a password? CLICK HERE - Forgot your password? CLICK HERE Subject: Subject:Message: : I've just yesterday gone back to my original modified stock valve. I was using a Rat 3:16 for awhile. I had to raise my operating pressure 25 psi over the mod stock, and my consistency along with accuracy was suffering. I previously enjoyed a spread of 9 fps over ten shots, I had my velocity set at 280 and never shot hot or under 275. Seeing some of the posts on sweetspotting and with some feedback I gave it a try and was dissapointed with the results (sorry guy's, maybe it's just me) it seemed like I almost went in a circle and ended up worse, oh well I can deal with 600 shots from a 68 3000. So now I've come to the conclusion that I should go back to my best setup. Blue Maddman springs front and back, modified stock valve (looks similar to a Turbo valve), wgp stock inline set to 250 psi. I have the green springs in right now and the reg is at 300 psi, but I'm going to go back to blues, drop 50 psi, and see if that tightens up the variance. I can arrange milling if your interested. : Razor : : : : I've been using mine for almost 2 years now with no problems other than wear (due due milling). I've run as low as 250 psi without flow problems or shootdown. It will work on any 2000+ stock cocker, or any pre 2000 with the use of a 2000+ back block. : : : Razor : : : : : : : is the ANS quick pull bolt good? im considering getting it because the design on the face is supposed to break up air more evenly and put a softer punch on the ball. the main reason for the question is, the site i purchace on says it "will only work on 2000 cockers". not 2000+. but arent the bolt shafts the same. the site is : : : : http://www.actionvillage.com/011-9010-850-5.html : : what valve do you use? [ Follow Ups ] [ Post Followup ] [ WARPIG Tech Talk - Autococker / Minicocker ]