Posted by: Razorpb on December 04, 2002 at 13:45:34

Try an Orracle valve, I'm extremely happy with it. I just went away from a Rat 3:16 and used the Orracle valve with the included spring set, sweetspotted and now get +/- 4 fps. A volumizer is alway a good idea to get more volume behind the valve. I polished my stock hammer and it works just fine. I recently went back to the stock WGP reg, the Ergo should be just fine, and easier to adjust (external) than my stock (internal) but once you set it correctly, you don't have to mess with it anyway. I've seen ANS inlines and the new Messiah reg on friends guns and don't see better performance for the high priced regs, compared to stock. Hope it helps, and saves some cash you'll need to spend on paint anyway with E-blade frame! Razor : At the moment I'm in the middle of building a custom electro cocker. This is my set up so far : vertical body 2000+ : E-blade : aka lightning bolt : micro rock : sto ram : Now I would like some suggestions on the internals. I'm not planning on running low pressure, because the eye will prevent chops. But I don't want shoot down in rapid fire. : Do you think i need a volumizer? : What valve is good if i don't plan on going low pressure? I was thinking on going with the a stock valve, but I'm not sure on the valves flow rate in very rapid fire? Mabye spooler valve? : Next is hammer? Is heavier or lighter better in an electro cocker? I could just go with a high polished stock hammer? : Springs Well i guess this depends on the hammer and valve : Finally An in line regulator. I'll be using compressed air. I was thinking go with the good old Ergo reg, but i have heard good things about the Vigalanty and maxflo. But i don't know if i want to dish out 100$ for them if they are not any better? : Thanks everyone.

Follow Ups: Re: Would like some suggestions... Vampyr 20:04:26 12/04/02 (9) Re: Would like some suggestions... Angry_Hippie 11:22:32 12/05/02 (8) Re: Would like some suggestions... Razorpb 13:16:31 12/05/02 (7) Re: Would like some suggestions... Angry_Hippie 15:03:31 12/05/02 (6) 30$ Christmas special? sKiTzO 01:07:45 12/06/02 (4) Re: 30$ Christmas special? Angry_Hippie 10:49:06 12/06/02 (3) LOL!!!! Re: 30$ Christmas special? sKiTzO 23:37:56 12/06/02 (0) LOL!!!! Re: 30$ Christmas special? sKiTzO 23:37:47 12/06/02 (0) LOL!!!! Re: 30$ Christmas special? sKiTzO 23:37:44 12/06/02 (0) Re: Would like some suggestions... Vampyr 21:26:35 12/05/02 (0) Post a Followup Show your name as: DefaultRealnameBothNickname E-Mail address (eg: joeschmoe@aol.com): Show your e-mail address? DefaultYesNo Your Password: Don't have a password? CLICK HERE - Forgot your password? CLICK HERE Subject: Subject:Message: : Try an Orracle valve, I'm extremely happy with it. I just went away from a Rat 3:16 and used the Orracle valve with the included spring set, sweetspotted and now get +/- 4 fps. A volumizer is alway a good idea to get more volume behind the valve. I polished my stock hammer and it works just fine. I recently went back to the stock WGP reg, the Ergo should be just fine, and easier to adjust (external) than my stock (internal) but once you set it correctly, you don't have to mess with it anyway. I've seen ANS inlines and the new Messiah reg on friends guns and don't see better performance for the high priced regs, compared to stock. Hope it helps, and saves some cash you'll need to spend on paint anyway with E-blade frame! : Razor : : : At the moment I'm in the middle of building a custom electro cocker. This is my set up so far : : vertical body 2000+ : : E-blade : : aka lightning bolt : : micro rock : : sto ram : : Now I would like some suggestions on the internals. I'm not planning on running low pressure, because the eye will prevent chops. But I don't want shoot down in rapid fire. : : Do you think i need a volumizer? : : What valve is good if i don't plan on going low pressure? I was thinking on going with the a stock valve, but I'm not sure on the valves flow rate in very rapid fire? Mabye spooler valve? : : Next is hammer? Is heavier or lighter better in an electro cocker? I could just go with a high polished stock hammer? : : Springs Well i guess this depends on the hammer and valve : : Finally An in line regulator. I'll be using compressed air. I was thinking go with the good old Ergo reg, but i have heard good things about the Vigalanty and maxflo. But i don't know if i want to dish out 100$ for them if they are not any better? : : Thanks everyone. [ Follow Ups ] [ Post Followup ] [ WARPIG Tech Talk - Autococker / Minicocker ]